Inner Tray Installation Procedure

Bundled Items

No.Bundled ItemQty
1Floor Bridge Unit B1
2Inner Tray1
-Stacker Support1

No.Bundled ItemQty
1Sheet holder2
2Paper holding sheet2
3Blindfold Covers1
4Blindfold sheet Assy1
5Screw M3 × 65
6Screw M3 × 81
Installation Procedure
Items to Prepare
  • Gloves
  • Cutter
  • Phillips (+) screwdriver
Minimum number of workers

1 person

Caution / 注意

Be sure to check the following precautions before installation.

  • All workers must read the installing procedure together before starting work.
  • Wear easy-to-move clothing, gloves and safety shoes and work with care for injuries etc.
  • Work with sufficient working space.
  • Work in the position with less load, and stop working immediately as you feel that the workload is too large.
  • All work must be done with the power off.
Installation Procedure
  1. Release the two hooks on floor bridge unit B (A), slide the cover (B), and remove it.
  2. Install the blind sheet assembly (B) to the floor bridge unit B (A).
  3. Install the cover removed in step 1.
  4. Peel off the release paper of the paper holding sheet (A), align the positioning holes with the dowels (B) of the sheet holder, and attach it.
  5. Remove one screw and remove the FD paper guide (A).

    • :3x8D/BK/P
  6. Attach the seat holder (C) by aligning the 4 hooks (B) of the seat holder with the 4 holes (A) on the bottom of the SCN unit, and slide it in the direction of the arrow to fix it.
  7. Install another Sheet holder in the same way.
  8. Pull the lever to open the Right Door Unit (A).
  9. Remove the Right Door Cable Cover while releasing the hook.
  10. Slide the D3 connector cover (A) in the direction of the arrow to release the 2 hooks and remove the connector cover.

  11. Disconnect the cables from the 2 connectors (A).

    Note / 補足
    • Cable colors are as follows.
      • Upper side: black
      • Lower side: white

  12. Remove 3 screws and pull the lever (A) to remove the D3 Unit (A).

    • : 4x8D/P
  13. Remove the 2 screws and remove the pre-ejection paper guide (A).

    • : 3x5D/TBD
  14. Remove the FD cable cover (A) by rotating it in the direction of the arrow while releasing the hook.
  15. Insert the tab (B) marked with a line into the hole (A) of floor bridge unit B, and attach floor bridge unit B (C).
  16. Check that the frame of floor bridge unit B protrudes from the 3 holes (A) on the paper output side, and tighten the 3 screws.

    • : 3x6D/P
  17. Tighten the 2 screws to secure Floor Bridge Unit B (A).

    • : 3x8D/P
  18. Connect the 3 cables of floor bridge unit B to the 3 connectors (A).

  19. Align the two dowels (A) with the two holes (B) and attach the FD cable cover (C).

    Assembly / 組み立て

    Make sure that the hook of the FD cable cover (A) is engaged.

  20. Align the hinge dowels with the two positioning holes (A), close the lever side, and attach the D3 unit (B).
  21. Tighten the 3 screws to secure D3 Unit (A).

    • : 4x8D/P
  22. Connect the 2 cables (A) to the connectors on the D3 unit and place them inside the hook (B).


    Caution / 注意

    Be careful not to confuse the connection destination of the cable.

  23. Attach the D3 connector cover (A).
  24. Insert the tab into the frame and attach the right door cable cover (A).
  25. Close the Right Door Unit.
  26. Hook the 3 hooks (B) of the Inner tray (A) to the 3 notches (C) of the frame, and attach the Inner tray.


  27. Install the blind cover (A) and secure it with one screw.

    • : 3x8D/BK/P
  28. Set the stacker support on the inner tray.