Pre-delivery Work Lists

Note / 補足

Pre-delivery work can be performed for this product in order to reduce the time spent at the customer's site during delivery and installation.
Carry out the work according to the option configuration and contract details with reference to the following. Part of the work content requires special treatment, so pay sufficient attention to the work content.

Product

Overview of operation

Note

Main Unit

  1. Unpacking (Main Unit Bundled Items and Unpacking Procedure)
  2. Carry out setting work (contract-related settings, FW update, date and time settings, initial filling, etc.).
  3. Start the service support mode and perform the Transport Preparation. (Notes about the transport for the pre-delivery works)
  4. Remove the Ink cartridges
  5. Attach the transportation parts (head, cap, right door).
  6. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. When performing FW update, it is recommended that all options to be installed are installed.
  3. Failure to do so may result in poor printing or ink leakage due to vibration during transportation. *If the print quality is not improved by head cleaning, the ink supply unit needs to be replaced.
  4. Failure to do so may result in product failure, ink leakage, or miscounting of remaining ink due to vibrations during transportation or tilting of the product.
  5. Failure to do so may result in product failure due to vibration during transportation.
  6. Failure to do so may result in product failure due to vibration during transportation.
Additional Cassette Unit
  1. Unpacking (Additional Cassette Unit Bundled Items and Unpacking Procedure)
  2. Attach to the main unit. (Additional Cassette Unit Installation Procedure)
  3. Perform FW update.
  4. Initial adjustment/setting cannot be performed. (Additional Cassette Unit Initial Adjustment Procedure)
  5. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. Side registration adjustment must be performed in the installation environment.
  5. Failure to do so may result in product failure due to vibration during transportation.
Floor Finisher


  1. Unpacking (Floor Finisher Bundled Items and Unpacking Procedure)
  2. Attach to the main unit. (Floor Finisher Installation Procedure)
  3. Perform FW update.
  4. Carry out initial adjustments and settings. (Floor Finisher Initial Adjustment Procedure)
  5. Release the connected state because it cannot be transported while attached to the main unit(Floor bridge units A and B can be transported in the installed state).
  6. Simple protection required before transportation. (Protecting the products to avoid damages while transporting)
  1. None
  2. If you plan to install the saddle unit or floor punch unit, do so in advance.
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. Work as needed.
  5. Transportation or movement while connected to the main unit is prohibited.
  6. Failure to do so may result in product failure due to vibration during transportation.

Saddle Unit

  1. Unpacking (Saddle Unit Bundled Items and Unpacking Procedure)
  2. Attach the floor finisher. (Saddle Unit Installation Procedure)
  3. Perform FW update.
  4. Carry out initial adjustments and settings. (Saddle Unit Initial Adjustment Procedure)
  5. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. Work as needed.
  5. Failure to do so may result in product failure due to vibration during transportation.

Floor Punch Unit

  1. Unpacking (Floor Punch Unit Bundled Items and Unpacking Procedure)
  2. Attach the floor finisher. (Floor Punch Unit Installation Procedure)
  3. Perform FW update.
  4. Carry out initial adjustments and settings. (Floor Punch Unit Initial Adjustment Procedure)
  5. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. Set according to the purpose of the attached punch unit.
  5. Failure to do so may result in product failure due to vibration during transportation.

Inner Finisher

  1. Unpacking (Inner Finisher Bundled Items and Unpacking Procedure)
  2. Attach to the main unit. (Inner Finisher Installation Procedure)
  3. Perform FW update.
  4. Carry out initial adjustments and settings. (Inner Finisher Initial Adjustment Procedure)
  5. Since it cannot be transported while attached to the main unit, it must be disconnected and repacked.(Inner bridge units can be transported in the installed state). (Protecting the products to avoid damages while transporting   )
  1. None
  2. If you plan to install the inner punch unit, do so in advance.
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. None
  5. Failure to do so may result in product failure due to vibration during transportation.

Inner Punch Unit

  1. Unpacking (Inner Punch Unit Bundled Items and Unpacking Procedure)
  2. Attach the inner finisher. (Inner Punch Unit Installation Procedure)
  3. Perform FW update.
  4. Carry out initial adjustments and settings. (Inner Punch Unit Initial Adjustment Procedure)
  5. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. None
  5. Failure to do so may result in product failure due to vibration during transportation.

High Capacity Unit

  1. Unpacking (High Capacity Unit Bundled Items and Unpacking Procedure)
  2. Attach to the main unit. (High Capacity Unit Installation Procedure)
  3. Perform FW update.
  4. Carry out initial adjustments and settings. (High Capacity Unit Initial Adjustment Procedure)
  5. The connected state is canceled because it cannot be transported while attached to the main unit.
  6. Simple protection required before transportation. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. Side registration adjustment must be performed in the installation environment.
  5. Transportation or movement while connected to the main unit is prohibited.
  6. Failure to do so may result in product failure due to vibration during transportation.
Caster Table
  1. Unpacking
  2. Attach to the main unit. (Caster Table Installation Procedure)
  3. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. Failure to do so may result in product failure due to vibration during transportation.
Inner Tray
  1. Unpacking
  2. Attach to the main unit. (Inner Tray Installation Procedure)
  3. Carry out initial adjustments and settings. (Inner Tray Initial Adjustment Procedure)
  4. Carry out a simple protection. (Protecting the products to avoid damages while transporting)
  1. None
  2. None
  3. None
  4. Failure to do so may result in product failure due to vibration during transportation.

Additional Network Interface Board

  1. Unpacking
  2. Attach to the main unit. (Extension Network Board Installation Procedure)
  3. Configure activation settings. (Additional Network Settings)
  4. Perform FW update. (Additional Network Settings)
  5. Configure initial settings. (Additional Network Settings)
  1. None
  2. None
  3. After enabling the special mode, perform FW update and initial settings. *Only for Japan model.
  4. When performing FW update, it is recommended that all options to be installed are installed.
  5. None
Extension Fax Board
  1. Unpacking
  2. Attach to the main unit. (Extension G3 Fax Board Installation Procedure)
  3. Configure activation settings. (Fax Settings )
  4. Perform FW update. (Fax Settings)
  5. Configure initial settings. (Fax Settings)
  1. None
  2. None
  3. After enabling the special mode, perform FW update and initial settings. *Only for Japan model.
    Activation is required to use IP FAX. (IP Fax/OCR Activation Procedure)
  4. When performing FW update, it is recommended that all options to be installed are installed.
  5. None
Wireless LAN unit
  1. Unpacking
  2. Attach to the main unit. (Wireless LAN Unit Installation Procedure)
  3. Perform initial settings and FW update. (Wireless LAN Setting)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
Additional HDD
  1. Unpacking
  2. Attach to the main unit. (Additional HDD Installation Procedure)
  3. Perform FW update.
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
OCR
  1. Unpacking
  2. Attach to the main unit. (OCR Option Installation Procedure)
  3. Perform FW update.
  4. Perform activation. (IP Fax/OCR Activation Procedure)
  1. None
  2. None
  3. When performing FW update, it is recommended that all options to be installed are installed.
  4. None
Authentication Table
  1. Since it cannot be transported while attached to the main unit, unpack and install in the installation environment.
  1. None